物理接続は 2 つのレイヤ 2 スイッチ間に実装されます。
そしてそれらの間のネットワーク接続を構成する必要があります。
私 。 LACP EtherChanneI を設定し、番号を 44 に設定します。設定します
インターフェイス EthernetO/O および SW2 を使用したスイッチ SWI と SW2 の間
両側に Ethernet0/1。 LACP モードは両端で一致する必要があります。
2. EtherChanneI をトランク リンクとして設定します。
3. 802.Iq タグを使用してトランク リンクを設定します。
4. VLAN「MONITORING」をタグなし VLAN として設定します。
イーサチャネル。
ガイドライン
これは、仮想デバイス上でタスクが実行されるラボ項目です。
* このラボ項目のタスクを表示するには、「タスク」タブを参照してください。
* デバイス コンソールにアクセスしてタスクを実行するには、[トポロジ] タブを参照してください。
* デバイス アイコンをクリックするか、コンソール ウィンドウ上のタブを使用すると、必要なすべてのデバイスでコンソールにアクセスできます。
* 必要な事前構成はすべて適用されています。
* デバイスのイネーブル パスワードまたはホスト名は変更しないでください。
* 次の項目に進む前に、設定を NVRAM に保存してください。
* 画面の下部にある [次へ] をクリックしてこのラボを送信し、次の質問に進みます。
※「次へ」をクリックするとラボが閉じられ、再度開くことはできません。

正解:
Solution is given below explanation.
Explanation:
To configure an LACP EtherChannel and number it as 44, configure it between switches SW1 and SW2 using interfaces Ethernet0/0 and Ethernet0/1 on both sides, configure the EtherChannel as a trunk link, configure the trunk link with 802.1q tags, and configure VLAN 'MONITORING' as the untagged VLAN of the EtherChannel, you need to follow these steps:
* On both SW1 and SW2, enter the global configuration mode by using the configure terminal command.
* On both SW1 and SW2, select the two interfaces that will form the EtherChannel by using the interface range ethernet 0/0 - 1 command. This will enter the interface range configuration mode.
* On both SW1 and SW2, set the protocol to LACP by using the channel-protocol lacp command.
* On both SW1 and SW2, assign the interfaces to an EtherChannel group number 44 by using the channel-group 44 mode active command. This will create a logical interface named Port-channel44 and set the LACP mode to active on both ends. The LACP mode must match on both ends for the EtherChannel to form.
* On both SW1 and SW2, exit the interface range configuration mode by using the exit command.
* On both SW1 and SW2, enter the Port-channel interface configuration mode by using the interface port- channel 44 command.
* On both SW1 and SW2, configure the Port-channel interface as a trunk link by using the switchport mode trunk command.
* On both SW1 and SW2, configure the Port-channel interface to use 802.1q tags for VLAN identification by using the switchport trunk encapsulation dot1q command.
* On both SW1 and SW2, configure VLAN 'MONITORING' as the untagged VLAN of the Port-channel interface by using the switchport trunk native vlan MONITORING command.
* On both SW1 and SW2, exit the Port-channel interface configuration mode by using the exit command.
* On both SW1 and SW2, save the configuration to NVRAM by using the copy running-config startup- config command.